NVIDIA Mellanox® MCX623106TN-CDAT — ConnectX-6 Dx EN 100GbE Dual-Port QSFP56 Adapter with Enhanced-SyncE and PTP
Technical Identity
The NVIDIA Mellanox® MCX623106TN-CDAT is a dual-port 100 Gigabit Ethernet standup PCIe adapter built on the ConnectX-6 Dx controller, with hardware Enhanced-SyncE and IEEE 1588 PTP timing including PPS In/Out. It presents two QSFP56 cages at 100GbE over a PCIe 4.0 x16 host interface, supplied with a tall bracket. The TN designation in MCX623106TN-CDAT denotes the timing variant without crypto. Protocol: Ethernet only. Condition: New, factory-sealed.
Specifications
Manufacturer documentation: NVIDIA ConnectX-6 Dx Ethernet adapter card user manual: specifications. T.E.S IT-SOLUTIONS is independent of NVIDIA.
What This Is NOT
NOT a crypto-enabled adapter. The TN designation on MCX623106TN-CDAT is the timing variant without inline crypto. IPsec and TLS offload require an AC or AE designation, for example MCX623106AC-CDAT. Do not specify this part where inline encryption offload is a requirement.
NOT an OCP 3.0 mezzanine card. The MCX623106TN-CDAT is a standup PCIe adapter. The OCP 3.0 ConnectX-6 Dx variants use MCX62343x part numbers and require an OCP 3.0 slot instead.
NOT a 200GbE adapter. The CDAT suffix denotes 100GbE per port. The 200GbE ConnectX-6 Dx variants use a VDAT suffix.
NOT an InfiniBand or VPI adapter. ConnectX-6 Dx is an Ethernet-only controller and cannot be switched to InfiniBand via mlxconfig. The VPI equivalent is the ConnectX-6 VPI family (MCX653xxx).
NOT a BlueField DPU. There are no onboard ARM cores and no DOCA runtime — this is a SmartNIC with hardware offloads and timing, not a programmable data-processing unit.
NOT verified for Multi-Host. Multi-Host ConnectX-6 Dx adapters carry an M designation and are not claimed here for MCX623106TN-CDAT.
NOT supplied with transceivers, DAC cables, a low-profile bracket, or PPS coaxial cabling.
Compatibility & Hard Constraints
Slot requirement: PCIe 4.0 x16. The card operates in a PCIe 3.0 x16 slot at reduced host bandwidth, which can constrain dual-port 100GbE line rate. It will not reach full throughput in an x8 slot.
Typical intended host platforms include: Dell PowerEdge, HPE ProLiant, Lenovo ThinkSystem and Supermicro rack servers with a PCIe 4.0 x16 slot. Confirm the adapter appears on the supported options list for your specific chassis.
Typical intended switch platforms include: NVIDIA Spectrum SN3700 / SN3420 and other 100GbE switches with QSFP56 or QSFP28 ports at 100GbE.
Timing deployment: the PPS In/Out headers require appropriate coaxial cabling and a grandmaster clock or GNSS source, none of which are supplied. Enhanced-SyncE and PTP behaviour depends on switch and network support for the chosen profile — verify the PTP profile (default, telecom G.8275.1, or other) end to end.
Bracket: supplied with a tall bracket. A low-profile chassis requires a separate bracket, not included.
Software dependencies:
NVIDIA MLNX_OFED or DOCA driver stack, or the in-box mlx5_core driver on modern Linux distributions
PTP hardware timestamping requires a matching PTP stack such as linuxptp, plus firmware support
Firmware and driver versions must be matched; mismatches are the most common cause of link, RoCE or timing-accuracy failures on this family
Pre-deployment verification: firmware level, driver version, port speed configuration, RoCE mode and PTP profile must be validated against your platform and network.
Frequently Asked Questions (FAQ)
What is the NVIDIA Mellanox MCX623106TN-CDAT?
The MCX623106TN-CDAT is a dual-port 100GbE QSFP56 standup PCIe adapter based on the ConnectX-6 Dx controller, with hardware Enhanced-SyncE and IEEE 1588 PTP timing including PPS In/Out, over a PCIe 4.0 x16 interface.
Does the MCX623106TN-CDAT include crypto offload?
No. The TN designation on MCX623106TN-CDAT is the timing variant without inline crypto. For IPsec or TLS offload, an AC or AE designation such as MCX623106AC-CDAT is required.
What timing features does the MCX623106TN-CDAT provide?
Enhanced-SyncE, IEEE 1588v2 PTP hardware timestamping, and PPS In and PPS Out headers. This makes MCX623106TN-CDAT suited to time-sensitive workloads such as financial trading capture, 5G fronthaul and broadcast media. PPS coaxial cabling and a clock source are not supplied.
Is the MCX623106TN-CDAT a standup PCIe card or OCP 3.0?
MCX623106TN-CDAT: Standup PCIe with a tall bracket. The OCP 3.0 ConnectX-6 Dx adapters use MCX62343x part numbers and need an OCP 3.0 slot, so the two cannot be substituted.
Does the MCX623106TN-CDAT support InfiniBand?
MCX623106TN-CDAT: No. ConnectX-6 Dx is Ethernet-only and cannot be reconfigured to InfiniBand. The ConnectX-6 VPI family (MCX653xxx) is the dual-protocol option.
What PCIe slot does the MCX623106TN-CDAT need?
MCX623106TN-CDAT: PCIe 4.0 x16 for full dual-port 100GbE throughput. It will operate in a PCIe 3.0 x16 slot at reduced host bandwidth, and will not reach line rate on both ports in an x8 slot.
What condition is supplied by T.E.S IT-SOLUTIONS?
New, factory-sealed. Each MCX623106TN-CDAT is identified against the part label and the adapter’s own board marking — confirming the TN timing designation and the CDAT 100GbE suffix — before shipping. with worldwide express B2B options from T.E.S IT-SOLUTIONS.
Why T.E.S IT-SOLUTIONS
Every unit ships with: (1) link verification where test topology is available, (2) EEPROM / vendor data check, (3) full cosmetic inspection, (4) professional anti-static packaging, (5) global B2B shipping from Haifa, Israel, (6) technical consultation for datacentre and timing network design at no extra cost. See tes-itsolutions.com.